fbpx

FORD RANGER 2011-2016 PX & PXII 3.2L 5 Cyl 4WD Turbo Diesel Exhaust

$1,449$2,099

Please ensure all exhaust system options have been selected to your preference – See ‘Options for exhaust’ below for more information

Beaudesert Exhaust’s full 2 3/4″ mandrel bent exhaust system to suit the Ford Ranger PX & PXII 3.2L non DPF.

 

Rugged
Rugged is our standard stainless steel system which is left as a raw finish.

Ultimate
Ultimate is our premium system which is made out of 304 grade stainless steel tube that we polish in-house.

 

Does your car have turbo lag or lack that pulling power? The factory exhaust restricts the airflow that is coming from the turbo. The pipes are too small and the components are not letting the engine breathe to the best of its ability. Majority of this can be solved with a new exhaust from the back of the turbo.
You will gain anywhere up to 8-12% improved performance just by letting the airflow out of the motor. Turbo lag will reduce resulting in better low down torque and giving you more pulling power out of the top of the rev range.

 

But be careful! Having an exhaust system too large for the motor can have the opposite effect! We have had some customers come back to us with aftermarket exhausts that are too big for the motor and in turn it has given them more turbo lag and less overall power gains. On some motors if the exhaust is too big you can run into some problems including over boosting or even boost spike of the turbo which will throw you into limp mode. This can be extremely dangerous if you are towing a caravan or trailer. This can happen from the turbo trying to spin too hard and fast, the ECU recognises this and can throw the car into limp mode.

 

We have found through research and development that a 2 3/4” exhaust system performs better than any other size for this vehicle. Not only have we completed real world testing, we also receive significant amounts of customer feedback regarding overall performance and fuel economy gains a Beaudesert Exhaust system can give your vehicle. Improvements are not only seen by those towing, but by everyday drivers who want more from their vehicle.

 

Mandrel bent, welded and manufactured in our workshop in South East Queensland, this high quality exhaust system includes:

  • Replacement Dump Pipe off turbo – 2mm wall thickness
  • 1/4in BSP Pyrometer fitting welded onto dump pipe – Standard in all systems
  • Euro 3 Standard 200 cell hi-flow Catalytic Converter – meets all emissions standards without restricting gas flow
  • Double braided stainless steel flex joint standard on all systems – inner and outer braid makes the flex joint stronger
  • Perforated straight through muffler or resonator as standard
  • No muffler pipe is available as an additional pipe for a louder note
  • This system can be purchased with no mufflers – designed for off road use only  Beaudesert Exhaust recommends purchasing a muffler or resonator then add the no muffler pipe. This is for legal reasons varying from state to state
  • 2 bolt 10mm 304 grade stainless steel flange plates
  • Reinforced brackets with supports – 12mm 304 grade stainless steel rod with knobs ensures the hangers don’t fall out of rubbers
  • Systems are available in Rugged Range or Ultimate Range (304 grade polished stainless steel)
  • Zinc plated locking nuts and bolts
  • Fitting Kit and easy to follow instructions
  • Boxed and bubble wrapped for freight
  • Freighted Australia wide with insurance in a prompt time frame

Options for exhaust

Changing the standard oval muffler to a small cylinder resonator for a louder note is at no charge.

The no muffler pipe is a replacement pipe that bolts in place of the muffler or resonator to gain maximum note.

If you wish to have both muffler section and no muffler pipe, select the muffler or resonator above and click here to add the no muffler pipe to your cart.

 

Please note: Our team will endeavour to dispatch your order as quickly as possible, however, some options when selected may require a longer fabrication time.

 

Would you like your system fitted?

Our experts over at Innovative Motorworks are the best to assist with all fitting needs. They are located at 6/14 Hopper Avenue, Ormeau, QLD, 4208.

Fitment for this system requires 4 hours.

Fitting cost will be charged on the day of your appointment.

 

Select fitting option at checkout and one of our staff members will be in contact with you to confirm availability.

*Please be aware additional charges may apply on the day of fitment if standard system needs modifications. Ensure all your aftermarket modifications (located on the checkout page) are listed correctly to try and avoid unexpected charges.

You may also like…