NISSAN PATROL 2012- Current Y62 5.6L Petrol Exhaust

Beaudesert Exhaust’s twin 2 1/2″ into single 3″ mandrel bent exhaust system to suit the Nissan Patrol Y62 5.6L.

Our recently redesigned system is our best yet!

Built for power and comfort, Beaudesert Exhaust’s Y62 Patrol sports exhaust really has Performance With Bite! Our complete mandrel bent stainless steel systems will be sure to last with your car, whatever you throw at it. Designed, Bent and Fabricated in South East Queensland, with focus on performance and flow with no drone.

Using the factory exhaust path, Beaudesert Exhaust’s system upsizes the engine pipes to 2.5” lowering exhaust pressure and temperature, whilst also increasing flow. These pipes then merge into a single 3” tube for the remainder of the system.

This system features self-locating V-band clamp system throughout. Not only does this make installation a breeze with the ability to make small adjustments as required, it also removes all exhaust gaskets so you will never have to worry about having an exhaust leak due to a failed gasket. All systems in the range feature braced 12mm 304 grade Stainless Steel hangers and muffler supports. The anti-vibration rubber that is installed on your original exhaust is retained, with a mount featured in the same location to bolt the rubber on.

Fitment has been tested with the Raslarr rear bar and LRA long range fuel tank.

Cat back exhaust – Bolting up behind the primary Catalytic Converters, the Cat back system increases exhaust flow and noise level can be selected with the choice of either rear muffler (mild note) or no rear muffler (louder note).

Full exhaust including Extractors and high flow Catalytic Converters – Expanding the above cat back design, Beaudesert Exhausts own 2mm wall thickness Stainless Steel, 2.5″ Tri-Y extractors and high flow Catalytic Converters. Supplied coated in Cerakote, these Extractors are ready to handle up to 1000°C. Dyno testing has seen an increase of 20hp and 50Nm of torque! Tuning isn’t required and no engine management issues by bolting onto a standard car.

Rugged
Rugged is our standard stainless steel system which is left as a raw finish.

Ultimate
Ultimate systems are complete High Polished 304 grade Stainless Steel. Polished to a high lustre these are the best systems available on the market.

Features:

• Double braided Stainless Steel flex joint standard on all systems
• Perforated straight through centre muffler and rear muffler
• No rear muffler pipe available for a louder note
• V-band clamps in 304 grade Stainless Steel
• Reinforced 12mm 304 grade Stainless Steel brackets with supports
• Systems are available in either Rugged Range or Ultimate Range (304 grade polished Stainless Steel)
• Fitting Kit and easy to follow instructions
• Boxed and bubble wrapped for freight
• Freighted Australia wide with insurance in a prompt time frame

Options for exhaust

The No Rear Muffler pipe is a replacement section that replaces the rear muffler to gain a louder note.

Please note: Our team will endeavour to dispatch your order as quickly as possible, however, some options when selected may require a longer fabrication time.

Would you like your system fitted?

Our experts over at Innovative Motorworks are the best to assist with all fitting needs. They are located at 6/14 Hopper Avenue, Ormeau, QLD, 4208.

Full System –

Fitment for this system requires all day.

Cat back System – 

Fitment for this system requires 2 hours.

Fitting cost will be charged on the day of your appointment.

Select fitting option at checkout and one of our staff members will be in contact with you to confirm availability.

*Please be aware additional charges may apply on the day of fitment if standard system needs modifications. Ensure all your aftermarket modifications (located on the checkout page) are listed correctly to try and avoid unexpected charges.